Ungodly ReignfallInstall guide by StixsworldHD

Troubleshooting

Find your symptom, open it and work down its causes. Most problems come down to a file in the wrong folder, and the one-paste check finds those in seconds.

BepInEx does not create its folders

After a launch, BepInEx holds only core and there is no LogOutput.log: BepInEx never started. Check, in this order:

  • The files are one folder too deep. winhttp.dll, doorstop_config.ini and the BepInEx folder must sit right next to Reignfall.exe. If there is a BepInEx_win_x86_5.4.23.5 folder inside your Reignfall folder, move everything in it up into the Reignfall folder and delete the empty folder.
  • It is the x64 build. The x86 winhttp.dll is 22,016 bytes (22 KB in Explorer); the x64 one is 26,112 bytes (26 KB). Replace it with the x86 build.
  • Doorstop is switched off. doorstop_config.ini must say enabled = true.
  • Your antivirus removed winhttp.dll. See antivirus.
  • You installed into another copy of Reignfall. Open the folder with Steam’s Manage, Browse local files, so you are in the copy Steam actually launches.
  • On Steam Deck or Linux you also need one launch option: see Steam Deck and Linux.
The mods do not load

BepInEx runs (its folders and log exist), but the log has no Loading [Ungodly …] lines and BepInEx\config has no Ungodly .cfg files.

  • The DLLs are not inside BepInEx\plugins. They must be in plugins or a folder inside it: not in BepInEx itself, not in core, and not next to Reignfall.exe.
  • Only the READMEs were copied. Copy the four folders that hold the DLLs.
  • The log says Skipping [Ungodly …] because of process filters (Reignfall.exe). The game was started through a renamed or different executable. These mods only load into Reignfall.exe, so launch the game from Steam.
  • You are reading an old log. BepInEx rewrites it at every start: launch again with the mods in place, then look.
The log says a plugin “targets a wrong version of BepInEx”

The line reads like Plugin [Ungodly Living Economy] targets a wrong version of BepInEx (5.4.23.5) and might not work until you update. Your BepInEx is older than 5.4.23. BepInEx still loads the mod, but it may not work properly.

Fix: close the game and extract BepInEx_win_x86_5.4.23.5.zip over your install as in step 6 of Install BepInEx, replacing files when asked. Your plugins and settings stay.

The log shows “Error loading [Ungodly …]”

BepInEx found the mod, but it failed while starting, and the lines right after that one say why. The usual cause is a Reignfall update that changed something the mod relies on: these builds were made for Reignfall v1.043. Check the version at the bottom left of the main menu, then send me the log (see getting help).

Pressing F6, F7, F8 or F9 does nothing
  • The mod did not load. Look for its Loading line in the log (how).
  • Your keyboard sends media keys. On many laptops the F-keys change volume or brightness by default: hold Fn while pressing, or turn on Fn Lock.
  • The key was changed. Each mod’s .cfg in BepInEx\config has a ToggleKey setting. MapGen also moves to a free key by itself if F6 is taken.
  • Another program uses the key. Overlays and recording tools sometimes claim F-keys for themselves. Change the key there, or change the mod’s ToggleKey.
The game stays paused after closing a window

The pause is shared by all four mods, so the game only resumes when every Ungodly window is closed. Another one is probably still open, perhaps behind the one you closed. Close it with its close button or its key, and the game carries on.

Stutter, low memory or a crash on a big map

Reignfall is a 32-bit game, so it can only use a limited amount of memory however much your PC has. Bigger maps and bigger armies use more of it.

  • Step the map size down in F6, Map Size (Colossal to Epic, or Epic to Huge), then start a new game.
  • Keep MapGen’s ground-texture cap at its default of 4096 px or lower.
  • MapGen’s Status tab shows memory use while you play.
  • In the Wave Spawner (F7), a high active squad limit also raises memory use. Lower it if waves grow very large.
An enlarged save lost its outer land

That happens when a save from an enlarged map loads without MapGen: Reignfall’s own loader drops every tile outside the stock map bounds.

  1. Quit without saving. Saving now would make the loss permanent.
  2. Put MapGen’s folder back in BepInEx\plugins.
  3. Load the save again. With MapGen installed it loads at the size it was saved, even with the generator switched off.

If the save was overwritten while the land was missing, the outer tiles are gone from that save.

Steam Deck and Linux (Proton)

Reignfall runs through Proton there, and Proton uses its own built-in winhttp.dll unless told otherwise. Install everything exactly as on Windows; on Steam Deck, switch to Desktop Mode and use Steam’s Manage, Browse local files to find the folder (on a default install it is ~/.local/share/Steam/steamapps/common/Reignfall). Then, in Steam, right-click Reignfall, choose Properties, and paste this into Launch options:

Steam launch options (Linux and Steam Deck only)
WINEDLLOVERRIDES="winhttp.dll=n,b" %command%

It makes Proton load the game folder’s winhttp.dll first, as described in BepInEx’s guide to running under Proton. Never add it on Windows.

Alternative: in protontricks, choose Reignfall, Select the default wineprefix, Run winecfg, open the Libraries tab, add winhttp and click OK.

If the mod windows show boxes instead of text, install the core fonts into Reignfall’s Proton prefix:

Terminal
protontricks 935930 corefonts
Antivirus flags or deletes winhttp.dll

winhttp.dll is Unity Doorstop, the small loader that starts BepInEx. Because it loads code into a game, some antivirus programs flag it on sight. The genuine x86 file from BepInEx_win_x86_5.4.23.5.zip has this SHA-256:

cc643b54484f694a8e0e6641cac79d74141009afc9e24d826f6fd7fd48fd182a

Check yours in PowerShell:

PowerShell
(Get-FileHash -Algorithm SHA256 'C:\Program Files (x86)\Steam\steamapps\common\Reignfall\winhttp.dll').Hash

If it matches, restore the file from quarantine and add an exclusion for your Reignfall folder. If it does not match, delete it and extract a fresh copy from the official zip.

Is Steam’s “Verify integrity of game files” safe?

Yes. Steam checks and repairs Reignfall’s own files; BepInEx and the mods are extra files Steam does not track, so they stay. If Steam reports that it replaced something, run the one-paste check afterwards.

Still stuck? Getting help
  1. Launch Reignfall once more so the log shows the problem, then quit.
  2. Run the one-paste check and copy what it prints.
  3. For a MapGen problem, first turn on Verbose log in the F6 window and make the problem happen again: MapGen logs every decision it makes.
  4. Send BepInEx\LogOutput.log, the check’s output and a short note of what you did and what you saw, via stixsworldhd.com.